We use cookies in order to personalize your site experience.
Shop
Arduino Nano Cable – USB 2.0 A to USB 2.0 Mini B
20,00 EGP- Compatible with Arduino Nano V3 (Mini USB port)
- USB 2.0 A to Mini-B 5-pin connector
- Supports data transfer rates up to 480 Mbps
- Compact 30cm length – perfect for desktop setups
- Plug-and-play; no drivers needed
Arduino Nano Type-C USB
250,00 EGP- Model Name/Number Arduino NANO
- Memory 32 KB of Which 2 KB Used By Bootloader
- Processor ATmega328
- USB 2.0 Ports Mini USB
- No. Of Cores Single
- Digital I/O Pin 22
- Weight 7g
Arduino Nano V3.0 CH340 Chip Board，Atmega328P
250,00 EGP- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
Arduino UNO R3 CH340G ATMega328P
330,00 EGP- ATmega328 SMD microcontroller with Arduino bootloader
- Operating voltage: 5V; input 7-12V recommended
- 14 digital I/O pins (6 PWM), 6 analog inputs
- 32 KB Flash memory, 16 MHz clock speed
- CH340 USB-to-serial interface (driver may be needed)
- Fully compatible with Arduino IDE and libraries
- Includes USB cable for easy programming
Arduino UNO R4 Minima
850,00 EGP- Same form factor as UNO R3
- Extra onboard peripherals
- Inbuilt HID Support
- Expanded Memory and Faster Clock Speed than before
Battery Charger 2 Cell For 18650 Battery
95,00 EGP- Charges 1–2 × 18650 Li-ion batteries simultaneously
- Independent slots with CC/CV charging
- LED indicators for charging/full status
- Built-in safety protections (overcharge, short-circuit, reverse polarity)
- Compact and lightweight for portability
- Input: AC 100–240V or DC 5V (USB, model dependent)
- Output: 4.2V per slot, ~500–1000mA charging current
Battery Charger for 18650 Li-ion 1 Cell YH-07
50,00 EGP-
Designed for 1×18650 Li-ion battery (3.7V)
-
Compact and portable charging dock
-
LED indicators: Red (charging), Green (fully charged)
-
Built-in protection: overcharge, short-circuit, reverse polarity
-
USB-powered – compatible with wall adapters, laptops, power banks
-
Ideal for flashlights, DIY projects, and battery testing
Battery Holder ( 1 x 18650 ) (3.7v)
12,00 EGP- 🔹 Holds 1 x 18650 battery (3.7V)
- 🔧 Pre-soldered leads for easy connection
- 🧱 Made of high-quality plastic
- 🛠️ Easy to install and use
- ⚠️ Compatible with standard 18650 batteries (not included)
Battery Holder for CR2025/CR2032 PCB Mount
4,50 EGPSecure and reliable coin cell battery holder for CR2025 or CR2032 batteries. Designed for PCB mounting, ideal for Arduino, RTC modules, and DIY electronics projects.
✅ Fits CR2025 and CR2032 coin cells
✅ PCB mount design for stable installation
✅ Easy battery replacement
✅ Durable and compact design
Battery Holder for CR2450 PCB Mount
8,00 EGPReliable coin cell battery holder designed for CR2450 batteries. Ideal for PCB mounting, making it perfect for Arduino, RTC modules, and low-power electronics.
✅ Compatible with CR2450 coin cells
✅ PCB mount design for stable and secure connection
✅ Easy battery insertion and replacement
✅ Durable and compact design
Battery Kit Breadboard (9V Input – Output 5V)
35,00 EGP- 9V input with regulated 5V output
- Breadboard-compatible design
- Plug-and-play for fast prototyping
- Ideal for Arduino, sensors, and logic circuits
- Includes 9V battery clip
