Shop
82D05 5V Digital Power Channel Amplifier Bluetooth Speaker Module
50,00 EGP-
5V Power Supply for USB or battery-powered projects
-
Built-in Bluetooth Receiver for wireless audio streaming
-
Stereo Output with left and right channel terminals
-
Compact Size ideal for DIY speakers and audio projects
-
Low Power Consumption with efficient digital amplification
A2212 1000KV Brushless Motor Kit – Efficient Power for RC Aircraft & DIY Projects
400,00 EGP-
1000KV Rating: Balanced RPM for stable, efficient flight
-
Complete Kit: Includes motor, X-mount, prop adapter, and screws
-
Lightweight: Weighs ~50g, perfect for park flyers and gliders
-
Durable Build: Features ball bearings, strong magnets, and quality windings
-
Easy Setup: Pre-soldered 3.5mm connectors for plug-and-play
-
Versatile Use: Ideal for RC planes, drones, gliders, and robotics
-
Budget-Friendly: Great value for beginners and DIY projects
AC/DC Power Adapter (5V 1A)
50,00 EGP- Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz.
- Input current (mA): 100.
- Output Power: 5V 1A.
- Input Plug: 2-Pin EU type.
- Output Plug: 5.5mm DC plug.
AMS1117 3.3V Voltage Regulator Power Module – 800mA Output for Arduino & Microcontrollers
20,00 EGPCompact 3.3V voltage regulator module based on the AMS1117 IC. Provides a stable 3.3V output up to 800mA, perfect for powering Arduino, ESP32, Raspberry Pi, and other 3.3V electronics.
✅ 3.3V regulated output
✅ Supports up to 800mA current
✅ Compact and easy-to-integrate module
✅ Ideal for microcontrollers and low-power electronics
Analog PH Sensor Kit
1.800,00 EGP- Module power supply: 5 VDC.
- Measuring temperature: 0-50 ℃.
- Response time: ≤ 1min.
- pH sensor with BNC connector.
- Gain adjustment Potentiometer.
- Power indicator LED.
Arduino Nano 3.0 Controller Board – FT232
290,00 EGP- Based on ATmega328 microcontroller
- FT232 USB-to-Serial driver for stable PC communication
- Compact and breadboard-friendly design
- 22 total I/O pins (14 Digital, 8 Analog)
- Supports serial, I2C, and SPI communication
- Onboard voltage regulator (5V & 3.3V)
- Preloaded with Arduino bootloader for easy programming
- Ideal for IoT, robotics, sensors, and embedded systems
Arduino Nano Cable – USB 2.0 A to USB 2.0 Mini B
20,00 EGP- Compatible with Arduino Nano V3 (Mini USB port)
- USB 2.0 A to Mini-B 5-pin connector
- Supports data transfer rates up to 480 Mbps
- Compact 30cm length – perfect for desktop setups
- Plug-and-play; no drivers needed
Arduino Nano Type-C USB
250,00 EGP- Model Name/Number Arduino NANO
- Memory 32 KB of Which 2 KB Used By Bootloader
- Processor ATmega328
- USB 2.0 Ports Mini USB
- No. Of Cores Single
- Digital I/O Pin 22
- Weight 7g
Arduino Nano V3.0 CH340 Chip Board,Atmega328P
250,00 EGP- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
Arduino UNO R3 CH340G ATMega328P
330,00 EGP- ATmega328 SMD microcontroller with Arduino bootloader
- Operating voltage: 5V; input 7-12V recommended
- 14 digital I/O pins (6 PWM), 6 analog inputs
- 32 KB Flash memory, 16 MHz clock speed
- CH340 USB-to-serial interface (driver may be needed)
- Fully compatible with Arduino IDE and libraries
- Includes USB cable for easy programming
Battery Charger 2 Cell For 18650 Battery
95,00 EGP- Charges 1–2 × 18650 Li-ion batteries simultaneously
- Independent slots with CC/CV charging
- LED indicators for charging/full status
- Built-in safety protections (overcharge, short-circuit, reverse polarity)
- Compact and lightweight for portability
- Input: AC 100–240V or DC 5V (USB, model dependent)
- Output: 4.2V per slot, ~500–1000mA charging current
Battery Charger for 18650 Li-ion 1 Cell YH-07
50,00 EGP-
Designed for 1×18650 Li-ion battery (3.7V)
-
Compact and portable charging dock
-
LED indicators: Red (charging), Green (fully charged)
-
Built-in protection: overcharge, short-circuit, reverse polarity
-
USB-powered – compatible with wall adapters, laptops, power banks
-
Ideal for flashlights, DIY projects, and battery testing
Battery Holder ( 1 x 18650 ) (3.7v)
12,00 EGP- 🔹 Holds 1 x 18650 battery (3.7V)
- 🔧 Pre-soldered leads for easy connection
- 🧱 Made of high-quality plastic
- 🛠️ Easy to install and use
- ⚠️ Compatible with standard 18650 batteries (not included)
Battery Holder for CR2025/CR2032 PCB Mount
4,50 EGPSecure and reliable coin cell battery holder for CR2025 or CR2032 batteries. Designed for PCB mounting, ideal for Arduino, RTC modules, and DIY electronics projects.
✅ Fits CR2025 and CR2032 coin cells
✅ PCB mount design for stable installation
✅ Easy battery replacement
✅ Durable and compact design
Battery Holder for CR2450 PCB Mount
8,00 EGPReliable coin cell battery holder designed for CR2450 batteries. Ideal for PCB mounting, making it perfect for Arduino, RTC modules, and low-power electronics.
✅ Compatible with CR2450 coin cells
✅ PCB mount design for stable and secure connection
✅ Easy battery insertion and replacement
✅ Durable and compact design
Battery Kit Breadboard (9V Input – Output 5V)
35,00 EGP- 9V input with regulated 5V output
- Breadboard-compatible design
- Plug-and-play for fast prototyping
- Ideal for Arduino, sensors, and logic circuits
- Includes 9V battery clip
BD243 DIY Prototyping Kit of Mini Tesla Coil
210,00 EGP- Type: Diy kits
- Input voltage: 9-12V, can be started with a 9V battery, but if there is an arc, the working voltage needs 12V.
- PCB board size: 3.1x4cm/1.22×1.57inch
- Color: As shown
- Quantity: 1Set